How To Install A Window In A Garage Wall
Step-by-footstep instructions for how to open up a wall, and mount and finish a pre-hung window.
Many windows are sold "pre-hung," meaning they come assembled with frames. Because you install the entire unit of measurement, installation of pre-hung windows is far easier than the method of building a frame and installing a window in information technology.
The chore does crave moderate carpentry skills and materials. If y'all practise non feel confident near tackling this job on your ain, call in a qualified window installer.
Following are full general instructions for how to install a pre-hung window. Directions will vary slightly from product to production, and then always read your manufacturer's instructions earlier beginning.
Besides note: Yous will need to open upward the interior side of the wall and rough frame an opening where the window will go. This rough framing will include extra wall studs on each side, a doubled 2-by-4 sill, and a header over the window, as discussed in depth inWall Framing for a Window.
Beneath are the steps for installing a new window in a newly-framed rough opening.
To gain an overview of this task, here is a pretty helpful video that shows a similar project. Some of the steps are a little dissimilar than the ones nosotros bear witness in the photos below, but the principles are basically the same. The primary differences are with how the moisture seal is applied because the video shows working with an opening where the siding has been removed beyond the trim.
Preparing a Rough Opening
ane From within the firm, drive nails through the wall to mark the corners of the window. Then, outside, outline the opening for the window.
2 Cutting through the siding and the sheathing with a power saw, making sure to use the correct blade. Place the window upward to the opening and check for fit. Go on trimming if necessary.
3 Identify the window into the opening to verify that it volition fit. Exist sure to make the opening slightly larger than the actual window. Check the manufacturer'south instructions to run into exactly how much space you should leave. Cut through the siding and drywall again, if necessary, to provide ample infinite.
four Line the opening with 8-inch-wide strips of wet seal and constrict them into the siding. Slit the corners of the wet seal diagonally with a utility knife, and fold the pieces toward the interior. Trim the strips if necessary until they extend just inside the interior edge of the opening. So staple them, working from the bottom up.
5 At this point, put two small 1/2-inch spacers at the bottom of the opening, virtually 1/2 inch in from the sides. Cheque for level, and add shims if needed.
Use dabs of silicone or two 6d (2-inch) nails per pair of shims to braze them to the opening (if you lot utilize nails, pre-drill boom holes). After they are secured, cut them so they are affluent with the siding.
Later on preparing the opening for a new window (come across How to Install a Window), information technology's time to actually mountain the window. Here are the steps to follow:
Mounting a Window
From outside the house, residuum the bottom of the window on the spacers, so slowly push button the superlative into the opening. Be sure information technology is right-side upwardly—it may have drain holes at the bottom that permit wet to drain.
Bulldoze a blast partway through the trim at ane of the upper corners. Check that the window is level, make any necessary adjustments to the shims, and and so finish driving the nail. Re-check the level.
So go inside and make sure everything looks okay from that side.
Drive nails at the other corners and then around the perimeter.
Insert shims forth the sides virtually the top and bottom of the window and at the midpoint, and accommodate them as needed until the window is plumb. Cheque to make certain the window is operational, and and so secure the window to the opening by driving nails into the brick mold or casing. Apply flashing and sealant (outside and within) co-ordinate to the manufacturer's instructions.
Finishing a Window
Affix the trim on the outside, and caulk the space between the window and the siding, according to the manufacturer'due south directions.
On the inside, check the window for level and add shims around the sides until the window is snug in the opening.
Using 8d (2 1/2-inch) finishing nails, nail through the jamb and the shims into the trimmer studs; use a nailset to set the nailheads just below the surface. Add together insulation between the jambs and the trimmer studs, cut the shims so they are flush with the wall, and so affix the interior trim.
Inside, yous tin can employ molding to complete your project: a stool, frock, and side casings for single- or double-hung windows.
Installing a Window In New Construction
Installing a window in new construction is easier than putting one in an existing wall, thanks to the fact that you don't have deal with interior wallboard, exterior siding, existing trim, and the like.
Here is an excellent video from This Quondam House on the right way to do this job:
Featured Resource: Notice Local Pre-Screened Window Installation Pros
Source: https://www.hometips.com/diy-how-to/window-installation.html
Posted by: leeyeas2002.blogspot.com
0 Response to "How To Install A Window In A Garage Wall"
Post a Comment